Oak CNC Controller kit

Centroid Oak CNC controller kit (part # 15000) includes:

– Oak control board
– Logic power supply with power leads
– Connector kit
– 15’ Shielded Ethernet cable
– Centroid CNC12 CNC Mill and Lathe FREE version of software, see below
– Typical CNC machine tool pre-programmed PLC Inputs and Outputs
– Mill and Lathe Conversational Programming Software
– Installation and Operator’s manuals PDF
– Full Size Paper Wiring Schematic
– DIY self service CNC support through Centroid Community CNC Forum which is Centroid   Technician monitored and maintained.
– Centroid CNC12 “FREE” version of CNC software. (Purchase Pro or Ultimate for additional feature set, see below.)

• Built in Motion Control CPU
• Mill and Lathe CNC software
• Reliable Ethernet communication with CNCPC
• Runs on Windows 10
• Compatible with CAD/CAM systems
• Runs Standard G & M Codes (see list in operator manuals)
• 4 Mb G code program size (unlimited optional)
• True G-code back plot graphics w cutter comp moves
• 2000 line accell decell look ahead
• 1200 blocks per second
• Feed rate override operator variable 0-200% at 1% increments
• Plug and Play dedicated MPG port
• Rapid rate override
• Spindle Control. on/off cw/cw, speed w/override
• 12-bit analog output 0-10 VDC for VFD control
• 16 optically isolated inputs, user configurable
• 9 fused relay outputs, user configurable
• Centroid Operator control pendant compatible
• Six Encoder Inputs
• Single 24 vdc logic power input
• Spindle Encoder RPM display
• Simple Menu Driven Operator Interface
• Stop and Restart Job at any point
• Tool Check, Jog and Restart at any point
• Cutter Compensation
• Conductive touch probe compatible
• Kinematic touch probe compatible
• Dedicated Touch Probe port

• 6 WCS G54 – G59 (12 more optional)
• 4th axis software (both G code and Conversational)
• Lube Pump control (user configurable to match pump type)
• MDI mode with recent command memory
• Programmable Auxiliary Function keys
• Multiple Language Support
• Stock PLC programs
• User editable PLC programming
• Part counter, Time, Time estimation
• Simple Future Software updates available
• G code editor
• Utility Menu
• Backup and Restore CNC config
• Message Display and Logs
• True Closed Loop CNC operation
• Unlimited Program Storage (only limited by hard drive size)
• Large easy to read DRO display
• Menu Driven Part setup
• Menu Driven Tool setup
• Menu driven machine configuration setup
• Fill in the blank Setup Menus
• Run Menu
• CNC control configuration menu
• Restart Job Automatically
• Any axis can be linear or rotary axis
• G-code smoothing (user adjustable)
• Auto Home to switch, user selectable direction per axis
• Jog to Home or Home to Marks
• Software Travel Limits (+ and – directions)
• User configurable Slow, Fast, Max rates
• User configurable axis motor acceleration

• Backlash compensation
• Gcode backplot checks work envelope
• G code backplot shows true cutter comp moves
• Vary part backplot speed and pause
  w/ G-code line display
• Real Time Part Graphics, shows tool position while running
• Optional Stops
• Subprograms and Macros
• Engraving compatible (short vector g code no problem)
• Threadmilling (Mill)
• Run in Inch or MM mode
• Tool Library
• Long part names
• Drilling and Tapping Cycles
• USB and Network Drive Compatible
• Keyboard Operator Control panel emulator,
• Xkeys USB control pad compatible
• Tool Life Management
• Ballscrew mapping table
• Control relays and contactors thru Manual or Program control
• User configurable custom DIY M-codes
• Canned Cycles
• Constant surface speed (lathe)
• Threading (lathe)
• Profiling with auto cleanout (lathe)
• Lathe canned cycles (thread, groove, chamfer, cutoff,turning diameter and end face,
• Scale input for DRO positional display of a manual axis
• X/Y axis Deskew
• Coordinate System Rotation