Masso CNC accessoires Archieven - Hardware CNC

Homing sensor – PoHome1IRPNP

Boudewijn van den Brink — Tue, 01 Jul 2025 15:40:20 +0000

Homing sensors are based on non-mechanical working principle, which makes them highly accurate and repeatable by not having any moving parts. The sensors have very high accuracy and a very low failure rate. PoLabs – PoHome homing sensor will ensure accuracy in tool changes, job fixtures, homing protocols, automation. The homing sensor is very easy to mount and set in the perfect position on a machine or device. The sensor has a status LED to indicate the state of the sensor. It is a simple device and it is compatible with most CNC machines.

Features

High accuracy with no moving parts,
Homing repeatability within 10 microns (0,01 mm),
Water-resistant – IP rating: IP64,
Wide working voltage range 5 – 24 VDC,
2 m long high-quality flex cable,
Easy mounting using M3 screws.

Sensor wiring

Brown – (5-24 VDC),
Blue – ( GND).
Black – (NO – Normally Open),
White – (NC – Normally Closed).

WARNING: Connecting the power polarity in reverse will damage the sensor!

Het bericht Homing sensor – PoHome1IRPNP verscheen eerst op Hardware CNC.

MASSO G3 Touch wiring module (3M cable)

Boudewijn van den Brink — Fri, 06 Dec 2024 15:32:03 +0000

This Set comes with the 3Meter long cable!

The MASSO G3 Touch Wiring Module is a seamlessly integrated extension board designed to facilitate effortless connections between your MASSO G3 Touch Controller and machinery. It’s the perfect solution for environments where significant cable lengths are needed to bridge the gap between the controller and your machine’s electronics.

Easy to install.
Makes signal wiring between MASSO G3 Touch and the machine simple.
If the wiring between the MASSO G3 Touch and machine gets damaged then the D connector cables can be easily replaced.
Includes two DB cables.

Wiring and Setup instructions: CLICK HERE

Easy to install.
Makes signal wiring between MASSO G3 Touch and the machine simple.
If the wiring between the MASSO G3 Touch and machine gets damaged then the D connector cables can be easily replaced.

Wiring and Setup instructions: CLICK HERE

Het bericht MASSO G3 Touch wiring module (3M cable) verscheen eerst op Hardware CNC.

MASSO Differential Receiver Module

Boudewijn van den Brink — Thu, 31 Oct 2024 16:11:06 +0000

The MASSO Differential Receiver Module is designed to provide support to Stepper or Servo motor drives that do not support advanced differential signals.

Differential signals provide great immunity to electromagnetic noise that can interfere with motor control signals and cause issues with motor positioning or might cause unexpected motion on the machine axis.

VFD drives for spindle motors and plasma cutting sources generate high electromagnetic noise and can interfere with motor position signals.
With differential signals, long cables with STEP and DIRECTION signals from the MASSO controller can be run to the motor drives.

Wiring and Setup instructions: CLICK HERE

Provide support to Stepper or Servo motor drives that do not support advanced differential signals.
Gives great immunity to electromagnetic noise that can interfere with motor control signals and cause issues with motion on the machine axis.
Can be used to control up to 5 axis motor drives.
Can also provide 5 volts so that no external 5 volt power supply is required.

The MASSO Differential Receiver Module is designed to provide support to Stepper or Servo motor drives that do not support advanced differential signals.
Differential signals provide great immunity to electromagnetic noise that can interfere with motor control signals and cause issues with motor positioning or might cause unexpected motion on the machine axis.
VFD drives for spindle motors and plasma cutting sources generate high electromagnetic noise and can interfere with motor position signals.
With differential signals, long cables with STEP and DIRECTION signals from the MASSO controller can be run to the motor drives.

Het bericht MASSO Differential Receiver Module verscheen eerst op Hardware CNC.

MASSO G3 Touch wiring module (5M cable)

Boudewijn van den Brink — Thu, 31 Oct 2024 16:07:14 +0000

This Set comes with the 5Meter long cable!

Easy to install.
Makes signal wiring between MASSO G3 Touch and the machine simple.
If the wiring between the MASSO G3 Touch and machine gets damaged then the D connector cables can be easily replaced.
Includes two DB cables.

Wiring and Setup instructions: CLICK HERE

Easy to install.
Makes signal wiring between MASSO G3 Touch and the machine simple.
If the wiring between the MASSO G3 Touch and machine gets damaged then the D connector cables can be easily replaced.

Wiring and Setup instructions: CLICK HERE

Het bericht MASSO G3 Touch wiring module (5M cable) verscheen eerst op Hardware CNC.

Encoder 1024PPR ABZ A-B-Z 6000RPM (met 5M kabels)

Boudewijn van den Brink — Tue, 09 Jan 2024 11:52:36 +0000

Included:

Encoder 1024PPR ABZ A-B-Z 6000RPM
Shielded cable 5 Meters

Features:

Shaft diameter	8mm
Output form	Push Pull
Output signal	A,B,Z A-B-Z phases
Housing diameter	58mm
Pulses	1024P/R
Supply voltage	5-30VDC
Load current	40mA
Protection grade	IP51

Technical Specification:

Electrical Specification
Output circuit	Open collector	Voltage output	Push pull output	Line driver output
Power Vcc	5~30	5~30	5±0.25 5~30	5±0.25 5~30
Current	≤80mA	≤80mA	≤80mA	≤150mA
Load current	40mA	40mA	40mA	60mA
Max Responding Frequency	300kHz	300kHz	300kHz	300kHz
Mechanical Specification
Max speed(r/min)	Starting Torque	Max. Shaft Loading	Shocking	Vibration
6000	<0.05Nm	Radial:20N, Axial:10N	50G/11ms	10G 10-2000Hz
Rotor Inertia	Working Temperature	Storage Temperature	Protection Grade	Weight
4*10-8Kgm2	-30~85℃	-35~95℃	IP51	270g

Connection Table:

Signal	A	B	Z	A(-)	B(-)	Z(-)	Vcc	GND	Shielded
Color	Green	White	Yellow	Brown	Gray	Orange	Red	Black	Copper net

9Pin Plug	5	3	2	7	6	8	1	4	9

Manual:

ISC5810 Encoder catalogue.pdf

Het bericht Encoder 1024PPR ABZ A-B-Z 6000RPM (met 5M kabels) verscheen eerst op Hardware CNC.

Encoder 2500PPR ABZ A-B-Z 6000RPM (met 5M kabels)

Boudewijn van den Brink — Tue, 12 Dec 2023 15:11:10 +0000

Included:

Encoder 2500PPR ABZ A-B-Z 6000RPM
Shielded cable 5 Meters

Features:

Shaft diameter	8mm
Output form	Push Pull
Output signal	A,B,Z A-B-Z phases
Housing diameter	58mm
Pulses	2500P/R
Supply voltage	5-30VDC
Load current	40mA
Protection grade	IP51

Technical Specification:

Electrical Specification
Output circuit	Open collector	Voltage output	Push pull output	Line driver output
Power Vcc	5~30	5~30	5±0.25 5~30	5±0.25 5~30
Current	≤80mA	≤80mA	≤80mA	≤150mA
Load current	40mA	40mA	40mA	60mA
Max Responding Frequency	300kHz	300kHz	300kHz	300kHz
Mechanical Specification
Max speed(r/min)	Starting Torque	Max. Shaft Loading	Shocking	Vibration
6000	<0.05Nm	Radial:20N, Axial:10N	50G/11ms	10G 10-2000Hz
Rotor Inertia	Working Temperature	Storage Temperature	Protection Grade	Weight
4*10-8Kgm2	-30~85℃	-35~95℃	IP51	270g

Connection Table:

Signal	A	B	Z	A(-)	B(-)	Z(-)	Vcc	GND	Shielded
Color	Green	White	Yellow	Brown	Gray	Orange	Red	Black	Copper net

9Pin Plug	5	3	2	7	6	8	1	4	9

Manual:

ISC5810 Encoder catalogue.pdf

Het bericht Encoder 2500PPR ABZ A-B-Z 6000RPM (met 5M kabels) verscheen eerst op Hardware CNC.

18.5 inch touchscreen metaal (1920×1080)

Boudewijn van den Brink — Fri, 05 May 2023 11:02:27 +0000

Dit Touchscreen paneel werkt met MASSO CNC, Centroid CNC, Windows en Linux. Wat uniek is aan dit model is dat het een autosleep functie heeft, hiermee gaat het scherm automatisch aan en uit bij het aanzetten van je controllers. Ook heeft de touchscreen een matte anti kras toplaag waardoor deze geschikt zijn voor zwaar industrieel gebruik.

Inputs van scherm:

Voeding
VGA
HDMI
USB A (voor touch)

Meegeleverd:

18.5″ Touchscreen 1920×1080 (16:9)
12VDC voeding (EU plug)
VGA kabel
USB kabel
VESA muurbeugel
2x montage rail
Handleiding

Het bericht 18.5 inch touchscreen metaal (1920×1080) verscheen eerst op Hardware CNC.

Pendant houder voor XHC BWGP

Boudewijn van den Brink — Mon, 17 Apr 2023 14:41:45 +0000

(pedant NOT included)

Het bericht Pendant houder voor XHC BWGP verscheen eerst op Hardware CNC.

Encoder 400PPR ABZ A-B-Z 6000RPM (met 5M kabels)

Boudewijn van den Brink — Fri, 13 Jan 2023 15:36:33 +0000

Features:

Shaft diameter	10mm
Output form	Push Pull
Output signal	A,B,Z A-B-Z phases
Housing diameter	58mm
Pulses	400P/R
Supply voltage	5-30VDC
Load current	40mA
Protection grade	IP51

Technical Specification:

Electrical Specification
Output circuit	Open collector	Voltage output	Push pull output	Line driver output
Power Vcc	5~30	5~30	5±0.25 5~30	5±0.25 5~30
Current	≤80mA	≤80mA	≤80mA	≤150mA
Load current	40mA	40mA	40mA	60mA
Max Responding Frequency	300kHz	300kHz	300kHz	300kHz
Mechanical Specification
Max speed(r/min)	Starting Torque	Max. Shaft Loading	Shocking	Vibration
6000	<0.05Nm	Radial:20N, Axial:10N	50G/11ms	10G 10-2000Hz
Rotor Inertia	Working Temperature	Storage Temperature	Protection Grade	Weight
4*10-8Kgm2	-30~85℃	-35~95℃	IP51	270g

Connection Table:

Signal	A	B	Z	A(-)	B(-)	Z(-)	Vcc	GND	Shielded
Color	Green	White	Yellow	Brown	Gray	Orange	Red	Black	Copper net

9Pin Plug	5	3	2	7	6	8	1	4	9

Manual:

ISC5810 Encoder catalogue.pdf

Het bericht Encoder 400PPR ABZ A-B-Z 6000RPM (met 5M kabels) verscheen eerst op Hardware CNC.